×
Follow Us
Page 5 of 5 FirstFirst ... 345
Results 41 to 45 of 45

Remembered NETA 2 Questions Help

 Jump to latest post
Page 5 of 5 FirstFirst ... 345
    #41
  1. Comx10 is offline Junior Member Pro Subscriber
    Join Date
    Dec 2021
    Posts
    9
    Reputation

    Not sure

    Quote Originally Posted by SecondGen View Post
    I'm thinking motor should stop and stay at highest level. A?
    I would have to agree with you there, regardless the motor needs to stop. whether it is A or D. These are the kind of questions that make the NETA test so difficult it seems to. The questions are almost open ended as it seems to me but in the real world it is exact and just go by the book and the manufacturer.

  2. #42
  3. Join Date
    Jun 2022
    Posts
    34
    Reputation
    1.) What is the small notch in a fuse for?

    Answer: Rejection Notch

    2.) Which has the greatest TIME difference?

    Answer a.) Extremely inverse



    6.) What is the highest pickup for a low voltage-480 system ground?


    Answer: d.) 1200 A

  4. #43
  5. Join Date
    Jun 2022
    Posts
    34
    Reputation

    Internal Resistance

    The internal resistance of a 20,000 ohm/volt voltmeter set on its 5 V range is

    A. 20,000
    B. 100,000
    C. 200,000
    D. 1,000,000

  6. #44
  7. Join Date
    Jun 2022
    Posts
    34
    Reputation

    Resistor

    A 12 k resistor, a 15 k resistor, and a 22 k resistor are in series with two 10 k resistors that are in parallel. The source voltage is 75 V. Current through the 15 k resistor is approximately

    [A]. 14 mA
    [B]. 1.4 mA
    [C]. 5 mA
    [D]. 50 mA

  8. #45
  9. Gage1374 is offline Junior Member Pro Subscriber
    Join Date
    Aug 2020
    Posts
    1
    Reputation
    [QUOTE=A_Powers1992;13879]To Whom it May Help:

    Here are some questions from my NETA 2 test that I remembered but did not know. All help is greatly appreciated! I did not pass....AGAIN. 406/410. 4 points!!! Third time is charm right? Ugh! Best of luck to you all. You're gonna need it.

    1.) What is the small notch in a fuse for?




    3.) If a motor and chain are present on an OLTC, once the tap is raised to the highest level and it's still giving a raise signal, what should the OLTC motor do?

    a.) motor stop, stay at raised level
    b.) motor continue til raise signal is gone
    c.) motor continue in reverse til back to neutral
    d.) motor stop, cool down

    4.) Which XFMR test has the ability to magnetize the windings?

    a.) Power Factor
    b.) TTR
    c.) Excitiation
    d.) Zero sequence impedance



    6.) What is the highest pickup for a low voltage-480 system ground?

    a.) 600 A
    b.) 800 A
    c.) 1000 A
    d.) 1200 A


    10.) Testing motor circuits would best be achieved by use of?

    a.) Ohmmeter
    b.) Phase-angle meter
    c.) Ammeter
    d.) ???


    1) The small nipple on a fuse is to ensure correct sized fused is used.

    3) a.) motor stop, stay at raised level

    6) d.) 1200 A

    10) a.) Ohmmeter

Page 5 of 5 FirstFirst ... 345
Subscribe

Share this thread

Related Topics

  1. NETA 4 Exam Questions 7/2018
    By MartyCoyne in forum NETA Level 4 Exam
    Replies: 29
    Last Post: June 22, 2022, 10:46 PM
  2. NETA 4 exam questions I am unsure about
    By mmacdonell in forum NETA Level 4 Exam
    Replies: 2
    Last Post: August 6, 2021, 07:15 AM
  3. Why so few questions for NETA 4 exam?
    By mmacdonell in forum NETA Level 4 Exam
    Replies: 3
    Last Post: February 10, 2020, 12:14 PM
  4. Challenging NETA questions after the test
    By adamstraub in forum NETA Level 3 Exam
    Replies: 1
    Last Post: October 24, 2019, 07:38 AM
  5. Couple NETA III Questions
    By jaycee91 in forum NETA Level 3 Exam
    Replies: 1
    Last Post: January 23, 2019, 01:14 PM

Tags for this Thread

Follow us


Explore TestGuy


NETA Certification Training


NICET Electrical Power Testing


Help and Support




You are viewing the archives. Enjoy new features and join the conversation at wiki.testguy.net